KRPMOD.DAT
The settings from the KRPMOD.DAT file have been integrated into the Configuration Editor (ISDConfigEditor.exe). The following list displays where to find the lines from the DAT file in the Configuration Editor (key name). Due to the constant further development of HiCAD, some entries are no longer required and are therefore marked with this symbol 
.
|
Line |
Description in KRPMOD.DAT |
German translation |
Key name |
|---|---|---|---|
|
3 |
Version of the KRPMOD.DAT file / 9 |
Versionsnummer |
|
|
10 |
Generate fields (common cylinder, pseudo /rotation fields) (AT THE MOMENT UNACCOUNTED FOR) Handling of figure structure: 0: Generate without sub-figures 1: Dissolve figure structure 2: Interpret figure structure 3: Transfer figure structure 2 |
Koerper generieren (allgemeiner Zylinder, Pseudo-/Rotationskoerper) 0: Ohne Subfiguren generieren 1: Figurenstruktur auflösen 2: Figurenstruktur interpretieren 3: Figurenstruktur übertragen |
Model > PartGeneration > Extruded and Revolved Solids > kg2dbaum |
|
16 |
Generate fields (common cylinder, pseudo /rotation fields) Open polylines: 0: Delete 1: Mark all open sections 2: Close 3: Generate 0 |
Koerper generieren (allgemeiner Zylinder, Pseudo-/Rotationskoerper) Nicht geschlossene Linienzüge: 0: Entfernen 1: Markierung aller offenen Teilstücke 2: Schließen 3: Generieren call kg2dneukrp( ) call setkg2dopt( 1, iclos,iec) call kg2dtest(0,iec) call kg2dini(0,iec) !nicht alles |
Model > PartGeneration > Extruded and Revolved Solids > kg2dneukrp |
|
22 |
Bores and subtractions: Open polylines: 0: Delete 1: Mark all open sections 2: Close 3: Enclose 0 |
Bohren und Ausnehmungen Nicht geschlossene Linienzüge: 0: Entfernen 1: Markierung aller offenen Teilstücke 2: Schließen 3: Generieren call kg2dbohr ( ) call setkg2dopt( 1, iclos,iec) call kg2dtest(0,iec) call kg2dini(0,iec) !nicht alles |
Model > PartGeneration > Extruded and Revolved Solids > kg2dbohr |
|
25 |
Graphic elements penetration test for field generation 1=active, 0=not 2=with min-max acceleration 2 |
Linienelemente-durchdringungstest bei Koerpergenerierung 1=aktiv 0=nicht 2=mit Minimax-Korrektur |
Model > PartGeneration > Extruded and Revolved Solids > kg2dsdtest |
|
33 |
Volume inversion test in modelling menu 1=activated 0=deactivated 1 |
Volumeninversionstest im Modelliermenue 1=aktiviert 0=deaktiviert |
Model > 3D Part Modelling > geonvolinv |
|
37 |
Triangulation for contortion 0: Prevent triangulation 1: Execute triangulation if necessary 2: Execute triangulation after query 2 |
Triangulation bei Verzerrungen 0: Triangulation verhindern 1: Triangulation ggf. ausführen 2: Triangulation nach Abfrage ausführen |
Model > 3D Part Modelling > geontria |
|
39 |
Mark contortion 0=mark not 1=mark |
Verzerrungen markieren 0=nicht markieren 1=markieren |
Model > 3D Part Modelling > geonfmark |
|
43 |
Mark surface: 2. Mark colour in surface selection menu (AT THE MOMENT UNACCOUNTED FOR) 8 |
Flaechen markieren |
|
|
47 |
Mark edge: Colour for 1-fold bound edge (AT THE MOMENT UNACCOUNTED FOR) 1 |
Kanten markieren einfach gebundene Kanten |
|
|
50 |
Colour for 2-fold bound edge (AT THE MOMENT UNACCOUNTED FOR) 2 |
Kanten markieren einfach gebundene Kanten |
|
|
61 |
Delete surfaces 0:Convert edges to individual edges 1:Delete edges only of given facets 2:Delete edges of complete cycles 3:like 2, cycled of 0/1 edges permitted 4:like 3, only omitted edges (AT THE MOMENT UNACCOUNTED FOR) 3 |
Flaechen löschen |
|
|
65 |
Merge edges: 0: no hyper edges (AT THE MOMENT UNACCOUNTED FOR) 1: hyper edges too 1 |
Kanten verschmelzen |
|
|
69 |
Allow surface compensation in modelling menu: 0: not allow 1: allow 1 |
Flaechenausgleich im Modelliermenue 1=aktiviert 0=deaktiviert |
Model > 3D Part Modelling > geonausgl |
|
74 |
Insert OK-query in modelling menu 0: insert (like V14) 1: not insert (not queried) 0 |
OK-Abfrage im Modelliermenue 0=aktiviert, 1=deaktiviert' if(iclos.eq.0)then geonokab=1 call vnwriti('ZOKF',1) !ok-Abfrage else geonokab=2 call vnwriti('ZOKF',0) !keine ok-Abfrage endif |
Model > 3D Part Modelling > geonokab |
|
77 |
Hidden edges in modelling menu for rectangle selection Account for (0=no, 1=yes) 1 |
Bei Rechteckauswahl im Modelliermenue ausgeblendete Kanten beruecksichtigen (0=nein, 1=ja) |
Model > 3D Part Modelling > rechausblend |
|
80 |
Shaded edges in modelling menu for rectangle selection Allow (0=no, 1=yes) 1 |
Rechteckauswahl im Modelliermenue in schattierten Ansichten ermoeglichen (0=nein, 1=ja) |
|
|
83 |
Hidden-line views in modelling menu for rectangle selection Extned to all hidden elements (0=no, 1=yes) 1 |
Rechteckauswahl im Modelliermenue in Hidden-line Ansichten ermoeglichen (0=nein, 1=ja) |
|
|
85 |
Mark rectangle selection in modelling menu (0=no, 1=monochrome 2=dichromic) 2 |
Rechteckauswahl im Modelliermenue markieren (0=nein, 1=1-Farbig 2=2-Farbig) |
|
|
88 |
Limits of inclination for inclined common cylinder Determine (0=no, 1=yes) 1 |
Bei schraegem allgemeinem Zylinder Grenzen der Schraegung ermitteln (0=nein, 1=ja) |
Model > PartGeneration > Extruded and Revolved Solids > kg2dschrvor |
|
91 |
Mark shaded for surface selection (0=no, 1=yes) 1 |
Markierungen am Polygonmodell erlauben (0=nein, 1=ja) |
Model > Miscellaneous > ishtmrkflag |
|
114 |
Position fitting points for c-edge sweep 0: automatic 1: interactive 0 |
|
|
|
117 |
Interactive transformation of the cross-section for c-edge sweep REM possible (0=no, 1=yes) 1 |
|
|
|
130 |
Local coordinate system for c-edge sweep 0: according to guideline 1: according to drawing coordinate system 2: according to last active coordinate system 1 |
Lokales Koordinatensystem fuer Kantenzug-Sweep 0: gemaess Leitlinie 1: gemaess Szene-Koordinatensystem 2: gemaess letztem aktivem Koordinatensystem |
Model > Miscellaneous > kg2dswks |
|
132 |
Keep or delete old sectional views after Boolean Operations: 0: Keep 1: Delete 0 |
|
|
