You find the file ANBASVAR.DAT - the Base Variant Definition file - in HiCAD subdirectory PlantParts\VariantStruct . Please refer to the Base Variant structure in your comment header of the file.
Extract from the file ANBASVAR.DAT:
# ** For Progr. AnVarEdit, HiCAD 3D Plant Engineering
**
# Definitions of input structure to support base variant
# entry identification:
# 1 = Start of block for variants with the appended names
# 2 = Start of block containing part components with the appended names
# 2A, 2B etc. = if their variable content can be equated,
# block sections are assigned the same character
# A button in square brackets on the drawing border, behind name specifications,
# can be used to activate this block section:
# Example:
2 Flange
1/3 [T1B3]
# Button designations:
# Above from left to right: T1,
T2, T3, T4
# Below from left to right: B1, B2, B3, B4
# Left from above to below: L1,
L2, L3, L4
# Right from above to below: R1,
R2, R3, R4
# 3 = this is followed by Variable name and associated designation,
# 3A, 3B usw etc. = Variables with content that can be equated,
# are assigned the same character
# H51=A0/2, H52=0 = specifies that the variant item belonging to
# the superior block section, can be switched off,
# if the variable is set to the value following
# "="
# 2A-, 3C- etc. = the content of objects identified by "-"
# can be taken over, but the object itself
# cannot be taken over by other objects
1 ARMEWKHF
2 Gen.
Parameter
3A- N:Nominal width
3A N2:Nominal width3
3B- L1:Length of con. 1 to cube centre
3B L2:Length of con. 2 to cube centre
2 Cube
[T3]
3 A0:Edge length
2B- Flange 1 [B3]
3 B1=0:Total thickness
3 F1:Offset of seal surface
3 D1:Flange diameter
3 D14:Diameter of seal surface
3C- D11:Ext. diameter of pipe socket
3D- S1:Wall thick. Of pipe socket
2B Flange 2 [R3]
3 B2=0:Total thickness
3 F2:Offset of seal surface
3 D2:Flange diameter
3 D24:Diameter of seal surface
3E- D21:Ext. diameter of pipe socket
3F- S2:Wall thick. of pipe socket
2A- Pipe1 [R4]
3C D19:Ext. diameter
3D S19:Wall thick
2A Pipe 2 [R2]
3E D29:Ext. diameter
3F S29:Wall thick.
2 Pipe 5 [T2]
3 D51:Diameter
3 H51=A0/2:Height from centre lines
2 Shaft [B1]
3 D52:Diameter
3 H52=0:Height
2 Lever [L1]
3 L53:Length
3 B53:Width
3 H53=0:Height
1 ARM3WKHF
2 Gen.
Parameter
3A- N:Nominal width
3A N3:Nominal width3
3B- L1:Length of con. 1 to cube centre
3 L:Total length
3B L3:Length of con. 3 to cube centre
2 Cube [L1]
3 A0:Edge length
2B- Flange 1/2 [L3R3]
3 B1=0:Total thickness
3 F1:Offset of seal surface
3 D1:Flange diameter
3 D14:Diameter of seal surface
3C- D11:Ext. diameter of pipe socket
3D- S1:Wall thick. of pipe socket
2B Flange 3 [B2]
3 B3=0:Total thickness
3 F3:Offset of seal surface
3 D3:Flange diameter
3 D34:Diameter of seal surface
3E- D31:Ext. diameter of pipe socket
3F- S3:Wall thick. of pipe socket
2A- Pipe 1/2 [B1B4]
3C D19:Ext. diameter
3D S19:Wall thick.
2A Pipe 3 [B3]
3E D39:Ext. diameter
3F S39:Wall thick.
2 Pipe 5 [T1]
3 D51:Diameter
3 H51=A0/2:Height from centre line
2 Shaft [R2]
3 D52:Diameter
3 H52=0:Height
2 Lever [T4]
3 L53:Length
3 B53:Width
3 H53=0:Height
|
© Copyright 1994-2018, ISD Software und Systeme GmbH |